PEES Components Logo
Imprint / Impressum | Policy / Datenschutz

Page not found

The System could not find the desired page.

Das System konnte die gewünschte Seite nicht finden.

Welcome at PEES COMPONENTS.

PEES Components GmbH provides electronic components for hydraulic drives.

With its long lasting experience of more than four decades in engineering and development PEES offers a broad portfolio of all kinds of control systems, ranging from simple hydraulic test equipment over analog amplifier modules to complex digital closed-loop controllers with modern fieldbus support.


PEES COMPONENTS is the Distributor of products from the former Company PEES Steuer- und Regelanlagen GmbH, Moers.

PEES COMPONENTS vertreibt Produkte der ehemaligen Firma PEES Steuer- und Regelanlagen GmbH aus Moers.

Products


Analogue Module - PEES Components

Analogue Module

The AN 4xx series has been especially developed for those applications where there was a need for compact and easy to install controllers.

As with all PEES Components units, these modules are extremely efficient and of superior quality.

  • easy to maintain, even for non-professionals
  • extremely fast end stages
  • internal DC/DC conversion, etc.
Euroformat - PEES Components

Euroformat

In this section you will find all units whose circuit board uses the European Format 100 x 160 (mm).

  • proven in tens of thousand of applications worldwide
  • sed for decades in applications home and abroad
Test-Device - PEES Components

Test-Device

The moment of truth in the initial commissioning of hydraulic systems and the appurtenant machines and facilities often occurs at the point where machines or other elements fail to behave as envisaged at the planning and design stage.

AN402

AN402

Servo Amplifier

The AN402 servo amplifier module is intended for the control of single magnet proportional valves. The control algorithm, ramps and similar command variables are derived exclusively from an external computer (PLC).

Visit
AN404

AN404

Servo Amplifier

The AN404 servo amplifier module is intended for the control of proportional valves with two magnets. The snap-on housing enables the AN404 module to be mounted on normal carrier rails in control cabinets. The electrical connections are via a terminal strip and a flat connector (enable input).

Visit
AN405

AN405

Servo Amplifier

The AN405 servo amplifier module is intended for the control of servo valves. It is available with various current ranges (±20mA, ±100mA, ± 200mA, ±300mA)

Visit
AN410

AN410

Pressure Controller

The AN410 pressure controller module is intended for pressure closed-loop-controls in conjunction with a pressure control valve. When the controller enable is switched off, the unit operates as an open loop controller in which the system pressure is adjusted in the usual manner by the valve current in conjunction with the control characteristic.

Visit
AN417

AN417

Setpoint Module

The AN417 setpoint module enables the universal input of setpoints for the control of servo and proportional valves. It has four setpoints and a polarity reverser.

Visit
AN418

AN418

Servo Amplifier

The AN418 servo amplifier module is intended for the control of proportional valves with two magnets. The snap-on housing enables the AN418 module to be mounted on normal carrier rails in control cabinets. The electrical connections are via a terminal strip and a flat connector (enable input).

Visit
AN419

AN419

Servo Amplifier

The AN419 servo amplifier module is intended for the control of single magnet roportional valves. The snap-on housing enables the AN419 module to be mounted on normal carrier rails in control cabinets. The electrical connections are via a terminal strip and a flat connector (enable input).

Visit
AN422

AN422

Servo Amplifier

The AN422 servo amplifier module is intended for the control of proportional valves with two magnets. The snap-on housing enables the AN422 module to be mounted on normal carrier rails in control cabinets. The electrical connections are via a terminal strip and a flat connector (enable input)

Visit
AN423

AN423

Servo Amplifier

The AN423 servo amplifier module is intended for the control of single magnet proportional valves. The snap-on housing enables the amplifier module to be mounted on normal carrier rails in control cabinets.

Visit
AN424

AN424

PID Controller Module

This PID controller module has been developed to meet the continuous demand for analog controller units in an easy-to-handle modular form.

Visit
AN430

AN430

Servo amplifier/PID Controller

The AN430 controller module has been developed, with the controller and servo amplifier accommodated in a single housing, for actuation of servo valves. The servo valve section can be supplied for four different current ranges (±20mA, ±100mA, ±200mA, ± 300mA).

Visit
ADN402

ADN402

The ADN 402 has been developed as a digital controller incorporating a valve amplifier for proportional valves with two magnets. The valve output stages function with fast de-excitation, with the result that the magnet current is adjusted to 0 in approx. 3-4ms.

Visit
ADN403

ADN403

The ADN 403 controller is a member of a modular-structure family of digital devices, which currently consists of eleven modules and is being continuously expanded. The ADN 403 is a high-speed cascade controller which permits implementation of up to three control loops.

Visit
ADN404

ADN404

digital controller

The ADN 404 has been developed as a digital controller with a valve amplifier for actuation of a servo-valve. The output stage is suitable in four ranges for +/– 20mA to 200mA valves.

Visit
ADN405

ADN405

The ADN 405 has been developed as a digital servo-amplifier for proportional valves featuring two magnets. The valve output stages function without fast de-excitation.

Visit
ADN406

ADN406

Digital Module

The ADN 406 has been developed as a digital servo-amplifier for proportional valves with one magnet. The valve output stages function with fast de-excitation, signifying that the magnet current can be set to 0 in approx. 3–4ms. Thanks to its high-speed output stage, the ADN 406 is extremely suitable for control tasks in the 0–30Hz frequency range.

Visit
ADN407

ADN407

The ADN 407 has been developed as a digital controller for actuation of servo and proportional valves in which the valve output stage is mounted on the valve. The controller is of dual type for operation of, for example, two axes synchronously as a CNC control system.

Visit
ADN408

ADN408

Mains Adapter/Distribution Module

The ADN 408 distribution unit has been specially developed for plant and system engineering, in order to eliminate the need to connect multiple cores to a single screw terminal. The module has the following outputs: 4 x 24V for supply of adjacent modules, and 4 x +/–15V or +/–10V. The +/–15V and +/–10V voltages are provided for supply of external sensors.

Visit
ADN409

ADN409

The ADN 409 has been developed as a CNC control system for operation with a directional proportional valve. The assembly consists of two modules, of types MD1 and MD14. The MD1 module is the basic module (equivalent to the ADN 402). The MD14 is the CNC expansion module. The MD14 CNC module is also used in other device combinations, due to the modular structure of this system.

Visit
ADN410

ADN410

The ADN 410 has been developed as a CNC control system for operation with a servo-valve. The assembly consists of two modules, of types MD3 and MD14. The MD3 is the basic module (equivalent to the ADN 404). The MD14 is the add-on CNC module.

Visit
ADN411

ADN411

The ADN 411 has been developed as a CNC control system for operation with a valve in which the electronics are mounted on the valve. The assembly consists of two modules, of types MD6 and MD14. The MD6 is the basic module (equivalent to ADN 407). The MD14 is the add-on CNC module.

Visit
ADN412

ADN412

The ADN 412 has been developed as a dual CNC control unit for operation with two correcting elements in which the electronics are mounted on the valves. The assembly consists of two modules, of types MD6 and MD15. MD6 is the basic module (equivalent to ADN 407). The MD15 is the add-on CNC module.

Visit
ADN600

ADN600

Digital Valve Amplifier

The ADN 600 is a valve amplifier for actuation of proportional valves, primarily in mobile driven machines. The device is can be operated at supply voltages from 11 to 28V dc, changeover from 24V supplies to 12V operating voltage occurs automatically by means of the built-in supply-voltage monitor.

Visit
ADN601

ADN601

Digital Valve Amplifier

The ADN 601 is a valve amplifier for actuation of two proportional valves, primarily in mobile driven machines. The device can be operated at supply voltages from 11 to 28V dc, changeover from 24V supplies to 12V operating voltage occurs automatically by means of the built-in supply-voltage monitor.

Visit
AN203

AN203

Servo Amplifier

The AN203 servo-amplifier has been designed for pressure control circuits with position-controlled pressure valves.

Visit
AN206

AN206

PID Controller

The AN206 controller module has been developed for use in plant engineering. Combination with other modular units permits assembly of any controller arrangements required. The P, I and D components can be adjusted internally or externally, via potentiometers.

Visit
AN207

AN207

PC Servo Amplifier

The AN207PC servo-amplifier has been specially designed for pressure control circuits in conjunction with a pressure adjustment valve. Thanks to the use of a PI controller, this module permits high accuracy between the Actual pressure value and the target-value (setpoint) input.

Visit
AN208

AN208

Setpoint Module

The AN208 setpoint module was designed for the application of setpoints in electrohydraulic open and closed loop control systems. With this module, it is possible to connect external setpoint potentiometers or the setpoints that are adjustable on the module can be connected internally.

Visit
AN209

AN209

Servo Amplifier

The AN209 servo amplifier has been designed to control single-magnet proportional valves and throttle-valves. The module is provided with various setpoint inputs: 4-20mA, 0-20mA, 0-5V, 0-10V, user selectable 10k /V An external enable input allows to lock the amplifier.

Visit
AN210

AN210

Universal OP Amplifier

The AN 210 module has been designed as a logical element for systems. The many different OP circuits, solder tags for components and the possibility of external interconnection for the individual OP amplifiers make this module suitable for a wide range of applications.

Visit
AN220

AN220

Servo Amplifier

The AN220 servo amplifier is suitable for controlling the most popular servo valves. The module provides current ranges of -20mA, -100mA, and -400mA for this purpose. The valve modulation can be adjusted by an internal/external limiter. In addition, the module is equipped with a PID controller, allowing a control system with a servo valve to be set up.

Visit
AN223

AN223

Measurement Socket Module

The AN 223 measurement socket module has 20 measurement sockets on the front plate. These allow rapid checking of the individual function stages of a system. In addition, 9 pairs of solder tags are provided for use as required.

Visit
AN230

AN230

Servo Amplifier

The AN 230 was especially designed as a amplifier to control proportinal valves without position feedback combined with the possibility to get the command signals direct from the amplifier. Hereby the command signals can be used as fixed values or together with an external potentiometer.

Visit
AN236

AN236

Servo Amplifier

The AN236 servo-amplifier has been specially developed for yoke positioning on an axial piston pump.

Visit
AN237

AN237

Servo Amplifier

The amplifier AN237 was developed to control proportional valves in a closed-loop control.

Visit
AN238

AN238

Servo Amplifier

The AN238 servo amplifier has been designed for the control of axial piston pumps valves in conjunction with servo valves. The module can be used as a pressure controller (zero stroke pump) or a volumetric flow controller by changing jumpers.

Visit
AN239

AN239

Setpoint Module

The AN239 setpoint module permits universal setpoint switching in electro-hydraulic open and closed loop control systems. It has five adjustable setpoints and a polarity reverser. An externally switchable and adjustable ramp is assigned to each setpoint.

Visit
AN240

AN240

U/I – I/U Converter Module

The AN 240 converter module has been developed to convert current signals to voltages and voltage signals to currents. A large selection of current and voltage ranges can be set thanks to the extensive input circuitry and simple positioning of jumpers.

Visit
AN241

AN241

Power Supply

The power supply AN 241 is a powerpack unit,which allows to supply installations and systems with 24VDC. The output of the unit are two voltages + 15VDC and 15VDC to supply analogues units. Additional be a auxiliary voltage made available.

Visit
AN527 / AN227

AN527 / AN227

Servo Amplifier

The AN527 servo amplifier has been designed for controlled proportional-stroke valves with two magnet coils.

Visit
AN528 / AN228

AN528 / AN228

Servo Amplifier

The amplifier AN528 was developed to control proportional valves in a closed-loop control. The AN527 is used as a basic unit. By connecting a special module it is possible to drive the AN527 as the AN528 together with positioning controlled proportional valves.

Visit
AN532 / AN232

AN532 / AN232

Servo Amplifier

The AN532 servo amplifier has been designed to control single-magnet proportional valves and throttle valves.

Visit
AN533 / AN233

AN533 / AN233

Servo Amplifier

The AN533 servo amplifier has been designed to control single-magnet proportional valves and throttle valves with position controller.

Visit
AN535 / AN135

AN535 / AN135

Servo Amplifier

The AN535 servo amplifier has been designed as a low-cost unit for single-magnet proportional valves.

Visit
HDC

HDC

Test and commissioning unit for hydraulic drive systems

The moment of truth in the initial commissioning of hydraulic systems and the appurtenant machines and facilities often occurs at the point where machines or other elements fail to behave as envisaged at the planning and design stage.

Visit
WPG1

WPG1

Tester for proportional directional-control and throttle valves

The WPG1 tester is used for actuation of proportional directional-control valves and also of non-position-controlled proportional throttle valves.

Visit